Animal Carcass Single Shaft Shredder for Efficiency

• After-sales Service: Lifelong Service
• Warranty: Two Years
• Type: Cutting Shredder
• Shipping Cost: Estimated freight per unit.: about shipping cost and estimated delivery time.
• Currency: US$
• Return&refunds: You can apply for a refund up to 30 days after receipt of the products.
• Model NO.: HRXS-J15
• Raw Material: Kitchen Waste Domestic Garbage
• Structure: Top Feed
• Knife Classification: Piece Knife Crusher
• Knife Roll: Solid Knife Roller
• Automation: Automatic
• Computerized: Computerized
• Certification: CE, ISO9001:2008, QS, GMP
• Frame: Integral Steel Frame
• Blade Material: 9crsi
• System: PC Automatic Control System
• Feeding Mode: Top Feed
• Power(Kw): 18.5*2
• Size (mm): 800*620*330
• Transport Package: Wooded Box and Bulk
• Specification: 5t/day
• Trademark: HRXS
• Origin: China
• HS Code: 84778000
• Production Capacity: 50000 Sets / Year
• Package Size: 200.00cm * 120.00cm * 180.00cm
• Package Gross Weight: 5000.000kg

Product Description

                                   Single shaft shredder for  animal carcass


1.Equipment introduction:

 The animal corpse shredder has the advantages of high efficiency, energy saving, environmental protection, intelligence and reliability. This equipment is a coarse and fine crusher, which skillfully combines the two-stage crushing into one. It can crush the complete animal carcass to the ideal particle size at one time. It is mainly suitable for crushing operations below 20mm. It is widely used in the crushing of whole pigs and cattle in harmless treatment plants, large farms and so on.





   
2. Performance characteristics of double shaft shredder:

The materials vertically fall into the high-speed rotating impeller from the upper part of the machine. Under the action of high-speed centrifugal force, they are separated with another part in the form of umbrella. The materials around the impeller produce high-speed impact and crushing.

After the materials collide with each other, they will form eddy currents between the impeller and the casing, collide and rub with each other for many times, and discharge directly from the lower part, Form a closed circuit for multiple cycles, and the screening equipment controls to achieve the required particle size of finished products.


3. Equipment operation:
 

5.1 Preparation:
Before starting the machine, first check whether there are materials, sundries and jamming in the crushing chamber; before
starting the machine every day, check whether all fasteners are completely fastened, and deal with them immediately if they are loose; check the lubrication of each rotating part before starting the machine

 5.2 Start up: 
The machine and transmission parts can be started up only after the inspection proves that they are in normal condition; the
machine must only be started under no load, otherwise it is easy to damage the motor, reducer, coupling, etc; start (jog the test run first) if there is any abnormal condition or abnormal sound, stop the start immediately, find out the cause and eliminate the fault before starting again

5.3Machine operation:
  When the machine is running, the maintenance personnel should often go to the side of the machine to observe the operation: whether the machine has abnormal sound. If it occurs, first determine the position, and then stop the machine for inspection and treatment; whether the temperature rise of the motor is too high.
   Under normal conditions, the maximum temperature shall not exceed 80 ºC; check whether the bolts at the rotating part are loose. If they are loose, stop the machine immediately.

5.4Shut dowu:
Before the machine stops working normally, the feeding shall be stopped first, and the crusher can be stopped only after all materials in the standby are broken. In case of machine failure or dangerous situation, the power supply can be cut off immediately.

4.Specifications and technical parameters of double shaft shredder:

 

Erial number	Model	Tear cavity size long×wide×high      (mm)	Blade diameter              (mm)	Blade   thickness           (mm)	Spindle   speed         (rpm)	Motor   power         (kw)	Tearing particle size               (mm)	Yield        (t/h)
1	2S0206	600×410×230	Φ200	15-30	12-25	11*2	3-30	0.3-0.6
2	2S0208	800×410×220	Φ200	15-30	12-25	15*2	3-30	0.5-1.0
3	2S0308	800×620×330	Φ300	15-35	10-22	18.5*2	3-30	0.8-1.6
4	2S0310	1000×620×330	Φ300	20-40	10-22	22*2	3-30	1.2-2.0
5	2S0312	1200×620×330	Φ300	20-40	9-16	30*2	3-30	1.8-2.8
6	2S0410	1000×830×440	Φ400	20-40	9-16	37*2	3-30	2.0-3.6
7	2S0412	1200×830×440	Φ400	20-45	9-15	45*2	3-30

5.Enterprise certification:

 

 

6.Transport: